IPMI
It is possible to control the power or connect a console to your nodes being managed by Warewulf by connecting to the BMC through the use of IPMI. We will discuss how to set this up below.
IPMI Settings
The common settings for the IPMI interfaces on all nodes can be set on a Profile level. The only field that would need to be assigned to each individual node would be the IP address.
The settings are only written to the IPMI interface if --ipmiwrite
is set to true. The write process happens at every boot of the node
through the script /warewulf/init.d/50-ipmi in the system
overlay.
If an individual node has different settings, you can set the IPMI settings for that specific node, overriding the default settings.
Here is a table outlining the fields on a Profile and Node which is
the same as the parameter that can be used when running wwctl
profile set or wwctl node set.
Parameter |
Profile |
Node |
Valid Values |
Default Value |
|---|---|---|---|---|
|
false |
true |
||
|
true |
true |
||
|
true |
true |
623 |
|
|
true |
true |
||
|
true |
true |
||
|
true |
true |
||
|
true |
true |
‘lan’ or ‘lanplus’ |
lan |
|
true |
true |
true or false |
false |
Reviewing Settings
There are multiple ways to review the IPMI settings. They can be reviewed from a Profile level, all the way down to a specific Node.
Profile View
# wwctl profile list -a
PROFILE FIELD PROFILE VALUE
=====================================================================================
default Id -- default
default comment -- This profile is automatically included for each node
default cluster -- --
default container -- sle-micro-5.3
default ipxe -- --
default runtime -- --
default wwinit -- --
default root -- --
default discoverable -- --
default init -- --
default asset -- --
default profile -- --
default default:type -- --
default default:onboot -- --
default default:netdev -- --
default default:hwaddr -- --
default default:ipaddr -- --
default default:ipaddr6 -- --
default default:netmask -- --
default default:gateway -- --
default default:mtu -- --
default default:primary -- --
Node View
# wwctl node list -a n001
NODE FIELD PROFILE VALUE
=====================================================================================
n001 Id -- n001
n001 comment default This profile is automatically included for each node
n001 cluster -- --
n001 container default sle-micro-5.3
n001 ipxe -- (default)
n001 runtime -- (generic)
n001 wwinit -- (wwinit)
n001 root -- (initramfs)
n001 discoverable -- --
n001 init -- (/sbin/init)
n001 asset -- --
n001 kerneloverride -- tw
n001 kernelargs -- (quiet crashkernel=no vga=791 net.naming-scheme=v238)
n001 ipmiaddr -- --
n001 ipminetmask -- --
n001 ipmiport -- --
n001 ipmigateway -- --
n001 ipmiuser -- --
n001 ipmipass -- --
n001 ipmiinterface -- --
n001 ipmiwrite -- --
n001 profile -- default
n001 default:type -- (ethernet)
n001 default:onboot -- --
n001 default:netdev -- eth0
n001 default:hwaddr -- 11:22:33:44:55:66
n001 default:ipaddr -- 10.0.2.1
n001 default:ipaddr6 -- --
n001 default:netmask -- 255.255.252.0
n001 default:gateway -- --
n001 default:mtu -- --
n001 default:primary -- true
Review Only IPMI Settings
The above views show you everything that is set on a Profile or Node level. That is a lot of detail. If you want to view key IPMI connecton details for a node or all nodes, you can do the following.
# wwctl node list -i
NODE NAME IPMI IPADDR IPMI PORT IPMI USERNAME IPMI INTERFACE
==================================================================================================
n001 192.168.1.11 -- hwadmin --
n002 192.168.1.12 -- hwadmin --
n003 192.168.1.13 -- hwadmin --
n004 192.168.1.14 -- hwadmin --
Power Commands
The power command can be used to manage the current power state of
your nodes through IPMI.
wwctl power [command] where [command] is one of:
- cycle
Turns the power off and then on
- off
Turns the power off
- on
Turns the power on
- reset
Issues a reset
- soft
Shutdown gracefully
- status
Shows current power status
Console
If your node is setup to use serial over lan (SOL), Warewulf can connect a console to the node.
# wwctl node console n001